Threaded Mode | Linear Mode

curv872 · 10-21-2011, 01:42 PM

(10-21-2011 01:28 PM)BostonR56S Wrote: Do you actually store your mixture in there? It'll evap if not airtight right? Or do you just use it when you need to mix your solution and use it to pour?

And do you have a good way of getting it out of the 5gal jug without pouring it all over yourself? lol
siphon?

I use this siphon

BostonR56S · 10-21-2011, 01:43 PM

Every two days???? You'd prob be better off getting tuned for meth, it'll prove more useful/effective at that rate.

I think something more like this would be better http://www.newpig.com/us/drum-accessorie...and-pumps/
The stainless if it fits in a 5 gal, as ur tube may deteriorate over time since its plastic/rubber? I didn't read it but if it's solvent/flammable approved then nvm

Buli · 10-21-2011, 01:49 PM

(10-21-2011 01:43 PM)BostonR56S Wrote: Every two days???? You'd prob be better off getting tuned for meth, it'll prove more useful/effective at that rate.

I think something more like this would be better http://www.newpig.com/us/drum-accessorie...and-pumps/
The stainless if it fits in a 5 gal, as ur tube may deteriorate over time since its plastic/rubber? I didn't read it but if it's solvent/flammable approved then nvm

"You can pump gasoline, alcohol, nitro, oil, transmission fluid or anti-freeze at a rate of 5 GPM by turning the hand crank in the direction of flow." It's safe with Alcohol.

killerfox · (This post was last modified: 10-21-2011 01:59 PM by killerfox.)

this is what I use with the nozzle at the bottom of the page:
http://www.vpracingfuels.com/page469715.html

I only store the Meth in it. It was only $25 at the local drag race track.

***ColinGreene*** · 10-21-2011, 03:12 PM

Ive been pouring straight out of the can into my tank, so far its worked alright.

ThumperGP · 10-21-2011, 03:21 PM

I see no need to switch containers. Keep it in the 5 gal...and pull the little spout out like I told you and it will work just fine. You know its clean, you know it won't evap, and it won't leak.

silhouette88 · 10-21-2011, 03:28 PM

Yep, pouring from the 5 gal pail has been working well for me too.

Buli · 10-21-2011, 04:29 PM

I don't pour straight from the can.

***ColinGreene*** · 10-22-2011, 01:40 AM

get some arm muscle, you will be fine. its just a aim thing. i pull the spout out and leave it that way so as not to have it break from repeated use.

BostonR56S · 10-23-2011, 08:47 PM

What to check if my IATs are still spiking over 110F? This is live reference only, no data log capabilities, just scan gauge.

Jet location: by dipstick post fmic elbow on intake tube
Jet size .7mm
Mixture roughly 65/35 w/m
Thres 11:45-12:00
Gain 12:30
No flow restrictor. Everything else was default.

I don't want to be draining this stuff into my engine at a ridiculous rate when I'm not even tuned with it. But should I not expect any results from even these settings? I can't tell a difference from when it's on and off. It's been 55F today so pretty cold but I figured when wot I'd still see at least close to ambient iat, as others have. I'm slightly confused.

When I primed the system Jeff wrote if it pulses stop and restart the sys test jumper. I did this a few times, and was pondering the small quick pulsations I was seeing. I called Blake and he said if the flow sensor isn't going crazy and it's staying steady it is ok. After this I tested it under the windshield wiper with the thres all the way ccw. At this point I realized it wasn't spraying. Saw the low level fluid light on, so I filled it up halfway with distiller water. All went well. Plugged into intake tube and filled tank with meth. Could the low level trigger have done anything??

Thanks for any input.