|
Here is how to wire Electric Water pump to Vipec
|
|
05-23-2012, 10:33 PM
Post: #1
|
|||
|
|||
|
Here is how to wire Electric Water pump to Vipec
This is using WIDEBAND instead of factory o2 sensors
pin 85 of relay is the ground control for relay take pin 85 to o2 engine harness connector pin 3 vipec settings are o2 sensor heater = injector 5 GP output condition 1 only SW condition 1 = ECT> 85C Sw condition 2= ECT< 80c So in this case: pump will start running at 85c and shut off after it drops below 80c  You can set these where you like this is just an example. Then setting the fan to help keep the water temps where you like You should never underestimate the predictability of stupidity "Tuning Matters" minimark Wrote: ....as silent as a freshly fallen snow on a crisp winter morning, a deafening hush falls across the land of Kool-Aid..... ![[Image: 76V0TaO.png?1]](http://i.imgur.com/76V0TaO.png?1) |
|||
|
|
05-23-2012, 10:42 PM
Post: #2
|
|||
|
|||
|
RE: Here is how to wire Electric Water pump to Vipec
Are you using the 02 sensor pin as the water pump controller? is that how i read that.
Sorry if that seems like a dumb question, i'm stuck in a hospital right now and i'm pretty tired. ![[Image: tumblr_m1rdjx4Vwg1qzkikho1_250.gif]](http://24.media.tumblr.com/tumblr_m1rdjx4Vwg1qzkikho1_250.gif) “Have you ever noticed how some people never
have the money to do it right, but can always find the money to do it twice ?” |
|||
|
|
|
05-23-2012, 10:46 PM
Post: #3
|
|||
|
|||
RE: Here is how to wire Electric Water pump to Vipec
(05-23-2012 10:42 PM)colingreene Wrote: Are you using the 02 sensor pin as the water pump controller? is that how i read that. by configuring the Vipec the way I posted will provide a ground in the Vipec for the water pump to come on when the water temp in the head gets past 85c and takes the ground away when it goes below the lower limit. Since you are NOT using the heaters for the o2 sensors (not in car) you can configure it as a GP output to run the water pump. If you don't have Meth hooked to AUX1 on the auxiliary harness you could have just run it to that instead. Either way the issue is fixed 
You should never underestimate the predictability of stupidity "Tuning Matters" minimark Wrote: ....as silent as a freshly fallen snow on a crisp winter morning, a deafening hush falls across the land of Kool-Aid..... |
|||
|
|
|
05-23-2012, 11:04 PM
Post: #4
|
|||
|
|||
|
RE: Here is how to wire Electric Water pump to Vipec
yeah ok that makes sense. and....
its probably really good to point out that this is only to feed power to a relay to control the voltage into the pump, not power the pump directly because the circuit will not handle the load, you need to wire the power directly off of the main power in on the side of the airbox. and use this to control the relay for the pump. “Have you ever noticed how some people never
have the money to do it right, but can always find the money to do it twice ?” |
|||
|
|
|
05-23-2012, 11:07 PM
Post: #5
|
|||
|
|||
|
RE: Here is how to wire Electric Water pump to Vipec
this will also allow the pump to stay energized after you shut the car down if the water temp is above the temp set in the ecu or at least til the timer kicks off de-energizing the pump
You should never underestimate the predictability of stupidity "Tuning Matters" minimark Wrote: ....as silent as a freshly fallen snow on a crisp winter morning, a deafening hush falls across the land of Kool-Aid..... |
|||
|
|
|
05-23-2012, 11:40 PM
Post: #6
|
|||
|
|||
|
RE: Here is how to wire Electric Water pump to Vipec
Hi Jan, thanks for posting this.
So I can wire that directly into the wires where I cut the O2 sensor off? ![[Image: dBzlY66.jpg?1]](http://i.imgur.com/dBzlY66.jpg?1) |
|||
|
|
|
05-24-2012, 12:03 AM
(This post was last modified: 05-24-2012 11:50 AM by ColinGreene.)
Post: #7
|
|||
|
|||
|
RE: Here is how to wire Electric Water pump to Vipec
yes. when im back ill find the wire diagram you need that tells you whats what.
![[Image: wiring02.jpg]](http://i1129.photobucket.com/albums/m520/jbskers/wiring02.jpg) “Have you ever noticed how some people never
have the money to do it right, but can always find the money to do it twice ?” |
|||
|
|
|
11-03-2012, 04:26 PM
Post: #8
|
|||
|
|||
|
Here is how to wire Electric Water pump to Vipec
Thanks for this - going to modify mine.
|
|||
|
|
|
09-27-2013, 06:27 PM
Post: #9
|
|||
|
|||
|
RE: Here is how to wire Electric Water pump to Vipec
I am trying to install the water pump with the relay but I am confused I need help.
I have the RL5 relay 40 amp. It has 85 (ground), 86, 87 and 30+battery. I am going to wire the 85 , to O2 engine harness connector pin 3. What about the others 86, 87, 30+battery. Powered by RMW |
|||
|
|
|
09-27-2013, 06:30 PM
Post: #10
|
|||
|
|||
|
RE: Here is how to wire Electric Water pump to Vipec
Do you have the two grounds in place? If so you only need to power the trigger.
“Have you ever noticed how some people never
have the money to do it right, but can always find the money to do it twice ?” |
|||
|
|
|
« Next Oldest | Next Newest »
|
User(s) browsing this thread: 3 Guest(s)