Aquamist HFS-3 and MINI Tank GB
|
07-20-2011, 03:29 PM
(This post was last modified: 07-20-2011 03:30 PM by cct1.)
Post: #21
|
|||
|
|||
RE: Aquamist HFS-3 and MINI Tank GB
Has anyone had any issues with tech inspection with the Meth kits? There is talk about requiring an SCCA tech checkout for some of the places I run, due to rising track insurance issues. 100% meth appears to be an issue with SCCA (although water is fine, and 50/50 mix MAY be fine). I haven't heard any issues with HPDE's, in fact it seems it's a nonissue from what I can tell, but there has been hints, rumors and allegations that 100% meth may be out. Looks like 50/50 will probably survive though.
I figure Jan's fuel cell setup is going to pass any tech, not 100% sure about the other tank though. The only good F56 is a dead F56
|
|||
07-20-2011, 03:33 PM
Post: #22
|
|||
|
|||
RE: Aquamist HFS-3 and MINI Tank GB
(07-20-2011 03:29 PM)cct1 Wrote: Has anyone had any issues with tech inspection with the Meth kits? There is talk about requiring an SCCA tech checkout for some of the places I run, due to rising track insurance issues. 100% meth appears to be an issue with SCCA (although water is fine, and 50/50 mix MAY be fine). I haven't heard any issues with HPDE's, in fact it seems it's a nonissue from what I can tell, but there has been hints, rumors and allegations that 100% meth may be out. Looks like 50/50 will probably survive though. mine is NOT an issue, braided lines and sealed fuel cell...........good to go 50/50 will NOT burn You should never underestimate the predictability of stupidity "Tuning Matters" minimark Wrote: ....as silent as a freshly fallen snow on a crisp winter morning, a deafening hush falls across the land of Kool-Aid..... |
|||
07-20-2011, 04:39 PM
Post: #23
|
|||
|
|||
RE: Aquamist HFS-3 and MINI Tank GB
How and what does the failsafe do/work? Trying to decide between the hfs-2 or hfs-3
If one opted for the hfs-2, what would be the cost to upgrade it to a hfs-3 later on? |
|||
07-20-2011, 05:04 PM
Post: #24
|
|||
|
|||
RE: Aquamist HFS-3 and MINI Tank GB
(07-20-2011 04:39 PM)curv872 Wrote: How and what does the failsafe do/work? Trying to decide between the hfs-2 or hfs-3 Do you have a 53 or 56? For the 56 it will cut boost by interrupting the wastegate solenoid. For the 53 there aren't a lot of good options. We are testing a way to drop boost on the 53, the parts are here, we just haven't had time to get it on the car. The cost to upgrade the 2 to the 3 is $250. |
|||
07-20-2011, 08:15 PM
Post: #25
|
|||
|
|||
RE: Aquamist HFS-3 and MINI Tank GB
(07-20-2011 05:04 PM)Howerton Engineering Wrote:(07-20-2011 04:39 PM)curv872 Wrote: How and what does the failsafe do/work? Trying to decide between the hfs-2 or hfs-3 r53 with Jan's head... what would typically trip the failsafe, low fluid, clogged valve, etc? |
|||
07-20-2011, 10:15 PM
Post: #26
|
|||
|
|||
RE: Aquamist HFS-3 and MINI Tank GB
lets see if we can get this group buy to twenty people! spread the word on other forums!
“Have you ever noticed how some people never
have the money to do it right, but can always find the money to do it twice ?” |
|||
07-20-2011, 10:39 PM
Post: #27
|
|||
|
|||
RE: Aquamist HFS-3 and MINI Tank GB
(07-20-2011 08:15 PM)curv872 Wrote:(07-20-2011 05:04 PM)Howerton Engineering Wrote:(07-20-2011 04:39 PM)curv872 Wrote: How and what does the failsafe do/work? Trying to decide between the hfs-2 or hfs-3 The system is setup so that by adjusting the potentiometers on the gauge face, you set a safe "window" for the injection. WE can go into more detail on setting this later. If the flow deviates, either above or below the the failsafe window, the failsafe will be tripped. Causes of the lower failsafe being tripped could be: partially clogged jet, plugged filter, blown pump fuse, etc. A cut line before the flow sensor would usually trip the low failsafe as the pressure would bleed off, a cut hose after the flowsensor will trip the upper failsafe. In the absence of a hard action(boost cut, etc) the gauge does show the failsafe has been tripped, but you could also hookup a buzzer or light as well. |
|||
07-21-2011, 12:13 AM
Post: #28
|
|||
|
|||
RE: Aquamist HFS-3 and MINI Tank GB
Just my luck. Bought my meth kit a week early!
Jeff makes awesome products! |
|||
07-21-2011, 08:34 AM
Post: #29
|
|||
|
|||
RE: Aquamist HFS-3 and MINI Tank GB
Well we'd love to get in on it Jeff and as per email we'd need the 76.2mm jet holding ring for pre Rotrex
We won't need a tank as we will have to make it fit All this is subject to me being given money from a long lost relative who has died ! I'll look forward to the email when you've closed the GB |
|||
07-21-2011, 09:51 AM
Post: #30
|
|||
|
|||
RE: Aquamist HFS-3 and MINI Tank GB
(07-21-2011 08:34 AM)brownpants Wrote: Well we'd love to get in on it Jeff and as per email we'd need the 76.2mm jet holding ring for pre Rotrex Ok, we'll do. Typically we have to sell the tank with the kit in the GB, but we can make it work with the pre-compressor sprayer. |
|||
« Next Oldest | Next Newest »
|
User(s) browsing this thread: 10 Guest(s)